In the hand-held baler, the pneumatic baler and the electric baler are two comparisons in the baler.
An efficient baler. Because they have external energy sources other than manual operations to provide kinetic energy. this
Days we will find more use of pneumatic balers! Because we found that the pneumatic baler is not just because
For a certain industry, it has a high demand for it, and the pneumatic baler is divided into two types.
Package material. One is a pneumatic steel belt baler, which is a pneumatic plastic belt baler! you could say so
Further increased the use of pneumatic balers.
Today, what is to be said is the slippage problem of pneumatic plastic belt balers and electric balers. hit
I don’t know if you have ever encountered it. When you buy the machine in operation, send it
Now the tape is not pulled by the tension button. Not because the pull is not enough, but the wheel is in one
I didn’t move the belt. This is when the baler packs and slips, so
It didn’t matter how the belt was pulled. So what should we do when we encounter the problem of belt slip?
To solve it?
In fact, there are two main reasons for the slipping of the baler: the time used by the first baler
Longer packaging opportunities slip. The second strap is too thin to slip. So how
Deal with it?
First of all, the first one: why the baler will take a long time to slip. Baler
The tightening principle is to drive the strapping drive by turning the tensioning wheel and dragging the stencil.
The tension is achieved, so we can see that there is a section in front of the welded strap.
The imprint of the friction, this is the trace left by the baler when it is tightened. And if the tension wheel
Or tighten the block because the long-term packing of the tooth has worn out enough to produce enough
When we rub the force, our straps will start to slip. So we can handle this problem.
To check if the tensioning wheel and the teeth that are fastening the teeth are intact, if any tooth grinding is found
The damage is serious and we need to replace it.
Second: the belt is too thin to slip. There are two ways to deal with this situation.
First, add a gasket on the lower part of the tensioning block of the baler. The high tensioning tooth is fast to make it tighten the wheel.
The position is closer to the required thickness of the strap. Second replacement of a thicker strap
Don’t think that replacing the strap is not cost-effective, and the too thin strap has a small breaking force. and
And the toughness is also low. For packaged security is not enough!
An efficient baler. Because they have external energy sources other than manual operations to provide kinetic energy. this
Days we will find more use of pneumatic balers! Because we found that the pneumatic baler is not just because
For a certain industry, it has a high demand for it, and the pneumatic baler is divided into two types.
Package material. One is a pneumatic steel belt baler, which is a pneumatic plastic belt baler! you could say so
Further increased the use of pneumatic balers.
Today, what is to be said is the slippage problem of pneumatic plastic belt balers and electric balers. hit
I don’t know if you have ever encountered it. When you buy the machine in operation, send it
Now the tape is not pulled by the tension button. Not because the pull is not enough, but the wheel is in one
I didn’t move the belt. This is when the baler packs and slips, so
It didn’t matter how the belt was pulled. So what should we do when we encounter the problem of belt slip?
To solve it?
In fact, there are two main reasons for the slipping of the baler: the time used by the first baler
Longer packaging opportunities slip. The second strap is too thin to slip. So how
Deal with it?
First of all, the first one: why the baler will take a long time to slip. Baler
The tightening principle is to drive the strapping drive by turning the tensioning wheel and dragging the stencil.
The tension is achieved, so we can see that there is a section in front of the welded strap.
The imprint of the friction, this is the trace left by the baler when it is tightened. And if the tension wheel
Or tighten the block because the long-term packing of the tooth has worn out enough to produce enough
When we rub the force, our straps will start to slip. So we can handle this problem.
To check if the tensioning wheel and the teeth that are fastening the teeth are intact, if any tooth grinding is found
The damage is serious and we need to replace it.
Second: the belt is too thin to slip. There are two ways to deal with this situation.
First, add a gasket on the lower part of the tensioning block of the baler. The high tensioning tooth is fast to make it tighten the wheel.
The position is closer to the required thickness of the strap. Second replacement of a thicker strap
Don’t think that replacing the strap is not cost-effective, and the too thin strap has a small breaking force. and
And the toughness is also low. For packaged security is not enough!